Programmable 3- Zone Temperature Cycling Cool and Heat Thermal Shock Testing Chamber for Electronic Products
Programmable 3- Zone Temperature Cycling Cool and Heat Thermal Shock Testing Chamber for Electronic Products makes the product under low and high temperature, and accelerates the failure caused by repeated temperature changes under normal operating conditions of items.During cold and hot shock tests, the transition between extreme temperatures was very rapid, exceeding 15℃ per minute.Alternatively, the temperature cycle uses a slower rate of high and low temperature change, exceeding 5℃ per minute.
6. GJB367.2-87 405
10. GB/T 2424.13-2002
11. GB/T 2423.22-2002
13. EIA 364-32
Application objects, including metal, plastic, rubber, electronics and other materials can be used as a basis to improve their products or reference.
Remark: We can achieve 1000cycles defrosting once, it is very ideal, the shorter the defrosting interval, the worse the airtightness of the device!
||+20℃ ～ +180℃
|2.High temp.chamber heat up time
||+20℃ ～ +180℃ 56min no load
||-10℃ ～ -65℃
|4.Low Temp.chamber pull down time
||-10℃ ～ -65℃ 57min no load
||W 400 × H 500 × D 400 mm (can customize)
||About W 1700 × H 1820 × D 1850 mm
||Have independent product test area, high temperature regenerative zone, low temperature storage area
||Stainless Steel Plate(SUS 304#)
High Temp.chamber:24k Glass fibre wool
Low Temp.chamber:PU Foam+Glass fibre wool
||Open wire electric heater
b.Stainless steel plate lengthened axle
a. Plane embedded handle
b. Back button: SUS 304#
c. Silicone foam strip
Germany Bock Semi-hermetic compressor or
Germany Semi-hermetic compressor
||R404A/R23 ,safe and no ozone damage
||Shell and tube condenser ( water cooled )
||High efficiency fin type auto load adjusted evaporator, no frost for long time operation.
High-precision expansion valve, oil separator, desiccant, etc. components
are imported using internationally renowned brands
Automatic adjustment of energy consumption output of the
Nitrogen welding, two-stage rotary vane vacuum pump, ensure that the internal cooling system clean and reliable.
water tray located at the bottom of the compressor to ensure condensate water drain through pipe freely at the rear of the chamber.
Since the cold chamber need huge cooling capacity for shocking, the chamber’s cooling mode is often designed as air-cooled or water-cooled.
Air-cooled type need installation environment:
The room must be equipped with exhauster and air conditioner to make sure heat dissipation timely.
It’s applied to small power products and cool areas.
Water-cooled type need installation conditions:
The customer must prepare water pipe and water tower (located outside) accordingly.
The water must be pure, or it will block the pipes and result in some maintenance trouble with time going.
It’s often applied to large system with the features of better heat dissipation, longer service time, low noise but slightly higher price if count the fee of water tower and water pipes.
During the whole business process, we offer Consultative Selling service.
1)Customer inquiry process:
Discussing testing requirements and technic details, suggested suitable products to customer to confirm. Then quote most suitable price according to customer requirements.
2)Specifications customize process:
Drawing related drawings to confirm with customer for customized requirements. Offer reference photoes to show the proucts appearance. Then, confirm the final solution and confirm final price with customer.
We offer below business term:
|Accepted Delivery Terms:
||FOB, CFR, CIF, EXW, DDP
|Accepted Payment Currency:
||USD, EUR, HKD, CNY
|Accepted Payment Type:
||T/T, L/C, Credit Card, PayPal, Western Union, Cash, Escrow
||Shenzhen, Guangzhou, Shanghai, Qingdao, Tianjing or rquired
4)Production and delivery process:
We will produce the machines according to confirmed PO requirements. Offering photoes to show production process.
After finish production, offer photoes to customer to confirm again with the machine. Then do own factory calibration or third party calibration(as customer requirements). Check and test all the details and then arrange packing.
Deliver the products in confirmed shipping time and inform customer.
5)Installation and after sale service:
Defines installing those products in the field and providing after-sales support.